Subject code AU3701 deals with the semester VII Anna University Regulation 2021, Engine And Chassis Components Design Syllabus. In this article, we discuss the AU3701 – Engine And Chassis Components Design Syllabus.
We would like to provide the syllabus to perform well in academics. Anna University Offers the B.E Automobile Engineering Syllabus including the seventh semester containing the AU3701 – Engine And Chassis Components Design Syllabus. We add every concept to the seventh-semester syllabus. You can get the proper information regarding the syllabus of the subject, it will assist you to excel in the academic examinations. You can also refer to our textbooks and references for more inclusive on the subject. Hope this information is useful. Don’t forget to share it with your classmates.
If you want to know more about the syllabus of B.E Automobile Engineering Syllabus connected to an affiliated institution’s four-year undergraduate degree program. We provide you with a detailed Year-wise, semester-wise, and Subject-wise syllabus in the following link B.E Automobile Engineering Syllabus Anna University Regulation 2021.
Aim Of Concept:
- The objective of this course is to prepare the students for understanding the design concept and principles involved in various engine components like cylinder, piston, connecting rod, crankshaft, flywheel, axle, suspension and steering systems.
AU3701 – Engine And Chassis Components Design Syllabus
Unit I: Introduction
Engineering materials – Introduction endurance limit, notch sensitivity. Tolerances, types of tolerances and fits, design considerations for interference fits, surface finish, surface roughness, Rankine’s formula – Tetmajer’s formula – Johnson formula- design of pushrods.
Unit II: Design Of Cylinder, Piston And Connecting ROD
Choice of material for cylinder and piston, design of cylinder, piston, and piston pin, piston rings, piston failures, lubrication of piston assembly. Material for connecting rod, determining minimum length of connecting rod, small end design, shank design, design of big end cap bolts.
Unit III: Design Of Crankshaft And Flywheel
Balancing of I.C. engines, significance of firing order. Material for crankshaft, design of crankshaft under bending and twisting, balancing weight calculations, development of short and long crank arms. Front and rear-end details. Determination of the mass of a flywheel for a given co-efficient of speed fluctuation. Engine flywheel – stresses on the rim of the flywheels. Design of hubs and arms of the flywheel, turning moment diagram.
Unit IV: Design Of Vehicle Frame, Suspension And Steering Systems
Study of loads-moments and stresses on frame members. Design of frame for passenger and commercial vehicle – Design of leaf Springs-Coil springs and torsion bar springs. Determination of optimum dimensions and proportions for steering linkages, ensuring minimum error in steering.
Unit V: Design Of Front Axle, Rear Axle And Drive Line
Analysis of loads-moments and stresses at different sections of front axle. Determination of bearing loads at Kingpin bearings. Wheel spindle bearings. Choice of Bearings. Design of front axle beam. Design of propeller shaft. Design details of final drive gearing. Design details of full floating, semi floating and three quarter floating rear shafts and rear axle housings and design aspects of final drive.
Text Books:
- Khurmi. R.S. & Gupta. J.K., “A text book of Machine Design”, Eurasia Publishing House (Pvt) Ltd, 2001.
- Giri, N.K., “Automobile Mechanics”, Khanna publishers, New Delhi, 2007.
References:
- Jain. R.K, “Machine Design”, Khanna Publishers, New Delhi, 2005.
- Dean Averns, “Automobile Chassis Design”, Illife Book Co., 2001.
- Heldt, P.M., “Automotive Chassis”, Chilton Book Co., 1992.
Related Posts On Semester – VII:
- AU3791 – Electrical and Hybrid Vehicles
- GE3791 – Human Values and Ethics
- AU3711 – Vehicle Maintenance and Testing Laboratory
- AU3712 – Summer Internship
Must Read For More: